各类车用电子部件：
· 车载摄像头
· 空调控制器
· 导航
· 组合灯
· 氛围灯
· 阅读灯
· 4G Tbox
· 5G Tbox
· 仪表
· 车窗控制开关
· 车窗电机
· 电子后视镜
· 驾驶角度传感器
· 车用无线电
· 暖通空调
· 防盗中控系统
· 驾驶角度传感器
· 控制器
· 显示器
· 照明
· 底盘位置传感器和控制器
· 轮胎压力传感器
· 倒车提醒装置
· ACP、VCP、CCH 功放
· 全球定位装置
· 直流马达（用于天窗、座椅、车门、车窗、雨刮器）
EMC测试项目：
· 辐射发射
· 传导发射
· 传导瞬态发射
· 辐射抗扰度测试—电波暗室试验法
· 大电流注入测试—代替法
· 大电流注入测试—闭环法
· 传导瞬态抗扰度测试—电源线
· 传导瞬态抗扰度测试—信号线、电感耦合钳试验法
· 传导瞬态抗扰度测试—信号线，直接电容耦合试验法
· 传导瞬态抗扰度测试—信号线，电容耦合钳试验法
· 磁场抗扰度测试
· 静电放电测试
测试标准：
| CE | ECE R10 | Unform provisions concerning the approval of vehicles with regard to electromagnetic compatibility. |
| CISPR | CISPR 25 | Vehicles, boats and internal combustion engines – Radio disturbance characteristics – Limits and methods of measurement for the protection of on-board receivers |
| EN | EN 13309 | Construction machinery – Electromagnetic compatibility of machines with internal power supply |
| EN | EN 50498 | Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles |
| EN | EN 55025 | Vehicles, boats and internal combustion engines. Radio disturbance characteristics. Limits and methods of measurement for the protection of on-board receivers |
| ISO | ISO 10605 | Road vehicles — Test methods for electrical disturbances from electrostatic discharge |
| ISO | ISO 11452-1 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 1: General principles and terminology |
| ISO | ISO 11452-2 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 2: Absorber-lined shielded enclosure |
| ISO | ISO 11452-3 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 3: Transverse electromagnetic mode (TEM) cell |
| ISO | ISO 11452-4 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 4: Bulk current injection (BCI) |
| ISO | ISO 11452-5 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 5: Stripline |
| ISO | ISO 11452-7 | Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 7: Direct radio frequency (RF) power injection |
| ISO | ISO 11452-8 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 8: Immunity to magnetic fields |
| ISO | ISO 11452-9 | Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 9: Portable transmitters |
| ISO | ISO 11452-10 | Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 10: Immunity to conducted disturbances in the extended audio frequency range |
| ISO | ISO 12097-3 | Road Vehicles – Airbag Components – Part 3: Testing of Inflator Assemblies |
| ISO | ISO 13766 | Earth-moving machinery Electromagnetic compatibility |
| ISO | ISO 16750-2 | Road vehicles. Environmental conditions and testing for electrical and electronic equipment. Electrical loads |
| ISO | ISO 17025 | General requirements for the competence of testing and calibration laboratories |
| ISO | ISO 7637-1 | Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations |
| ISO | ISO 7637-1-2 | |
| ISO | ISO 7637-2 | Road vehicles — Electrical disturbances from conduction and coupling — Part 2: Electrical transient conduction along supply lines only |
| ISO | ISO 7637-3 | Road vehicles — Electrical disturbances from conduction and coupling — Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines |
| SAE | J1113-3 | Conducted Immunity, 250 kHz to 400 MHz, Direct Injection of Radio Frequency (RF) Power |
| SAE | J1113-4 | IMMUNITY TO RADIATED ELECTROMAGNETIC FIELDS.BULK CURRENT INJECTION (BCI) METHOD |
| SAE | J1113-11 | Immunity to Conducted Transients on Power Leads |
| SAE | J1113-12 | Electrical Interference by Conduction and CouplingCapacitive and Inductive Coupling via Lines Other than Supply Lines |
| SAE | J1113-13 | Electromagnetic Compatibility Measurement Procedure for Vehicle ComponentsPart 13: Immunity to Electrostatic Discharge |
| SAE | J1113-21 | Electronmagnetic Compatibility Measurement Procedure for Vehicle Components – Part 21: Immunity to Electromagnetic Fields, 30 MHz to 18 GHz, Absorber-Lined Chamber |
| SAE | J1113-22 | Electromagnetic Compatibility Measurement Procedure for Vehicle Components—Part 22—Immunity to Radiated Magnetic Fields |
| SAE | J1113-23 | Electromagnetic Compatibility Measurement Procedure for Vehicle Components – Immunity to Radiated Electromagnetic Fields, 10 kHz to 200 MHz, Strip Line Method, Recommended Practice |
| SAE | J1113-24 | Immunity to Radiated Electromagnetic Fields; 10 kHz to 200 MHz—Crawford TEM Cell and 10 kHz to 5 GHz—Wideband TEM Cell |
| SAE | J1113-41 | Limits and Methods of Measurement of Radio Disturbance Characteristics of Components and Modules for the Protection of Receivers Used on Board Vehicles |
| SAE | J1113-42 | Electromagnetic Compatibility—Component Test Procedure—Part 42—Conducted Transient Emissions |
| ECE R10 | CISPR 25 | EN 13309 | EN 50498 |
| EN 55025 | ISO 10605 | ISO 11452-1 | ISO 11452-2 |
| ISO 11452-3 | ISO 11452-4 | ISO 11452-5 | ISO 11452-7 |
| ISO 11452-8 | ISO 11452-9 | ISO 11452-10 | ISO 12097-3 |
| ISO 13766 | ISO 16750-2 | ISO 17025 | ISO 7637-1 |
| ISO 7637-1-2 | ISO 7637-2 | ISO 7637-3 | J1113-3 |
| J1113-4 | J1113-11 | J1113-12 | J1113-13 |
| J1113-21 | J1113-22 | J1113-23 | J1113-24 |
| J1113-41 | J1113-42 |
专业设备：
· 3米电波暗室
· CISPR25电波暗室
· 罗德与施瓦茨ESR3 EMI接收机
· 夏弗纳CBA 9436射频功放
· CPI VZS/C-6963J2功放
· AR FL7006场强探头
· 罗德与施瓦茨E8257D信号发生器
· Milmega AS0104-400/200ST RF射频功放
· AR100W1000B 100W功放
· 特测NSG437静电放电枪
· EM Test传导瞬态抗扰度测试系统
· 泰克TDS 3054B示波器
· 高压人工网络
· EM Test连续波模拟器
